Parts & Accessories

$59.99
Our thru-axle kit comes with everything you need to mount most 12x142 thru-axle bikes on your KICKR SNAP indoor trainer. This accessory will work with all editions of the Wahoo KICKR SNAP.
It includes the following:
- Threaded axle spacer M12 x 1.75 Coarse
- M12 x 1.5 Medium
- M12 x 1.0 Fine
- End Cap

$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims.
21mm width fits:
- ZTR Olympic
- ZTR Iron Cross
- ZTR 355
- ZTR Alpine
- ZTR Crest
- ZTR Alpha 340 (2 layers)
- ZTR Alpha 400 (2 layers)
- Most road clincher rims
25mm width fits:
- ZTR 355 (26", 650b, 29")
- ZTR Crest
- Crest MK3
- ZTR Arch EX
- ZTR Flow EX
- Crest S1
27mm width fits:
- ZTR Flow EX
- ZTR Bravo
- ZTR Hugo 52mm
- Arch S1
- ZTR Rapid 28
- ZTR Rapid 30
- Arch MK3
30mm width fits:
- ZTR Flow MK3

$54.00
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season.
- When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out.
- The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability.
- No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench.
- Designed, built, and quality tested in the USA. Proven around the world.
Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

$39.99
Designed to be stiff and durable enough to meet the demands of modern mountain bike riding, the Ritchey WCS BOOST fork thru-axle offers confidence and control for whatever kind of trails you're into.
- Type: thru-axle
- Material: 7075 Alloy
- Axle Length: 135mm
- Diameter: 15mm
- Thread diameter: M15
- Thread pitch: 1.2mm
- Head: hex 6mm
- Weight: 63g
- Color: black

$24.99
Converts CenterLock hubs to accept 6-bolt rotors
- Available for standard Quick Release as well as Thru-Axle hubs
- Extruded alloy collar with CNC shoulder pins and lock ring
- Eliminates the need for rotor bolts

$22.99 - $37.99
Elite Series skewers for fat bike applications
AL6061 alloy lever with CrMo axle
Available for 135mm, 150mm, 170mm, and 190mm OLD spacing

$17.99 - $27.99
- AL6061 alloy tubeless Presta valve
- Includes 2 O-rings, one standard profile and one aero profile, for an airtight seal on any rim
- Removable valve core for installing sealant
- Additional replacement valve cores sold separately
- Sold individually

$20.99 - $22.99
- CNC-machined tubeless valves with aluminum stem nut and valve core wrench cap
- Fit for most other tubeless rims and wheel

$47.00
Your riding doesn’t need to stop when the weather gets cold.
Features
- Giant road thru-axle trainer axle
- Alloy construction
- For use on 2017+ Giant road bikes with a 142x12mm rear thru-axle

$10.00
Using Easton End Caps allows you to utilize the versatility of Easton Wheels. Easton wheels are interchangeable with a variety of wheel mounting standards.

$37.90
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and to perfectly position the lever.
- Ratcheting system tightens skewers with turns rather than a cam
- Lever can be rotated into an ideal position after tightening

$44.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever.
- Ratcheting system tightens skewers with turns rather than a cam
- Lever can be rotated into an ideal position after tightening
- Conical X12 washer, compatible with Syntace X-12 system
- Thread Pitch: 12 x 1.0mm

$12.99
- Plastic spoke covers in a variety of colors
- 300mm cut to fit length
- 36 pieces - enough for one wheel
- Increases visibility and demands attention

$24.00
Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).

$151.00
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation.
The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included.
- 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center
- Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels
- Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels
- Includes cassette spacer
- Material: Aluminum

$70.00
- Wheel bearing kit front/rear
- Bearing dimensions: 17 x 30 x 7mm
- Material: steel
- 2 pieces

$19.00 - $31.00
Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.

$7.00
Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm.
Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.

$390.00
- Kits include Freehub body with CeramicSpeed bearings pre-installed for easy installation onto the wheel
- Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings

$390.00
- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available
- Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings
- Kits include Freehub body with CeramicSpeed

$206.00
Zipp Speed Weaponry Rear Axle Conversion Kit
- Not to be used on 188 V6 or earlier rear hubs
- Only to be used to convert Zipp's 188 V7 10-speed rear hubs to 11-speed

$227.00
Zipp Speed Weaponry Rear Axle Conversion Kits
- Converts a road disc into a track disc rear
- Fits black 2013 188 V8 disc hubs only
- Fits Zipp 900 and Super-9 Discs

$21.00
These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals.
Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.

$19.00
A simple solution for completing the Zipp aerodynamic package by covering the valve access hole on most disc wheels. Black, self-adhesive oval patches with the Z logo, in a package of five.
Page 1 of 15
Next page